AOC V24T Uživatelský manuál

USER’S MANUAL

Connection and preparation of TV set Mounting the TV set to a wall This unit conforms to VESA standards for wall mounting. Please refer to the specif

Turn On/Off the LCD 1. Turn on the LCD： Switch on the AC power supply on the back of the TV set and press the Power key on the remote controller

Searching Press the “TV” key on the remote controller to switch to the TV signal source, then press the “Menu” key on the remote controller or the

About the control panel and interface PANNEL CONTROL KNOBS Input: Press this button to change input source. Menu: Press this button to

SOURCE INTERFACE Several signal source devices can be connected to your TV set. The following diagram shows how to connect them. Tips: If you want

SOURCE INTERFACE Antenna Input: Insert the antenna connector into the antenna jack of the TV. The interface is a 75 Ω coaxial cable input. Video/S

SOURCE INTERFACE Component Input： Connect the sound and picture of the component signal source (DVD, laser disc player, video recorder or camera, e

SOURCE INTERFACE Computer signal and computer audio input: Connect the host signal to the computer input port at the back of the TV via the VGA sign

OPERATING INSTRUCTIONS TO USE THE REMOTE CONTROL

OPERATING INSTRUCTIONS To install the remote control batteries 1. Remove the battery cover. Insert two AAA batteries into the battery compartment.

ThankyouverymuchforchoosingtheLCDTV.We suggest that you spend several minutes to read carefully this manual before you install an

TO USE THE MENU 1. Press the Menu button to display Main Menu. 2. Use the V- or V+ to select the function to be adjusted. 3. Use the P- or P+ to en

TO USE THE MENU Picture Setting Brightness Adjustable between 0-100, set the backlight brightness of the picture.Contrast Adjustable between 0-1

TO USE THE MENU Sound Setting (the same for all modes) Sound Mode Switch between the five preset sound modesBass Adjust the intensity of the bass

TO USE THE MENU Function Setting MENU language Select the OSD language between English/SimplifiedChinese/Russina/Portuguese/French/Spanish. Imag

TO USE THE MENU Tuning (the following menus appear only in TV mode) Channel Nr. Display the number of the current TV channel.Frequency Displa

TO USE THE MENU PC Setting (the following menus appear only in the PC mode) Auto Config Automatically config the optimal position of the pict

Tips Care of the screen Do not rub or strike the screen with anything hard as this may scratch, mar, or damage the screen permanently. Unplug the scre

Product Specification Model V22t V24t Display area 546mm (21.5”) 598mm (23.6”) Recommend frequency 1920 x1080 1920 x1080 Visual ang

SUPPORTED RESOLUTION PRRESET PC MODE STANDARD RESOLUTION HORIZONTAL FREQUENCY (kHz) VERTICAL FREQUENCY (kHz) VGA 640×480 @60Hz DMT 31.469 59.940 V

SUPPORTED RESOLUTION WSXGA 1680X1050 @60Hz CVT16:10 65.290 59.954 WSXGA 1680X1050 @60Hz RB CVT16:10 64.674 59.883 HD 1920×1080@60Hz 67.500 60.00

USER’S MANUAL Table Of Contents Important safety instructions ... ...3 Read before operating equipment...

Before Calling Service Please make these simple checks before calling service. These tips may save you time and money since charges for receiver insta

Before Calling Service Snowy picture and noise *Check the antenna connection Horizontal dotted line *This may be caused by electrical interference (e

GLOSSARY Audio / Video Inputs Located on the rear and the front of the receiver these connectors (RCA phono type plug) are used for the input of audi

Function setting... ... ...21 Tuning... ... ...22 PC images... ...

IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment 1. Read these instructions。 2. Keep these instructions。 3. Heed all warnings. 4.

IMPORTANT SAFETY INSTRUCTIONS 19. Tilt/Stability – All televisions must comply with recommended international global safety standards for tilt an

Connection and preparation of TV set Packing Contents

Connection and preparation of TV set Attaching the Base Take the TV set and the base out of the carton and assemble them with the screws in the a

Connection and preparation of TV set Place the TV on a solid surface 1. Ensure that the TV is placed in a position to allow free flow of air. Do n